“橡胶切条机”参数说明
切刀: | 多刀 | 类型: | 电动 |
品牌: | 三兴 | 样式: | 立式 |
尺寸: | 1200*1000*1200mm |
“橡胶切条机”详细介绍
SX-RCA-08(翻滚)切条机 (size: L*W*H 1200*1000*1200mm)
RUBBER STRIP CUTTING MACHINE
用途:用于橡胶切条、切纸等。
特点:1.装有防护装置在使用时安全快捷。
2.翻滚切割,三个刀片设计,切料速度快,效率高。
3.送料速度可调,裁断宽度可调。
Purpose:This machine is used for cutting the rubber, paper etc.
Advantage: 1. Equiped with safety cover to secure safety on working .
2. Revolving blade cuts rubber in high speed and efficiency, with three blade edges.
3. adjusting the width of rubber strip through the speed button on the side.
使用说明:(中文:参考之前的广告册)
英文如下:
1. when operating, do not cut rubber in double-deck at one time, which will cause
the MOTOR to be too hot and broken. If the Material-sending Roller can not run smoothly, please shutdown at once; meanwhile, if there are odds and ends at knife edge, please clean up in time. Do stop the power before cleaning.
2. No iron or stone in the material; if any, take them
away at once, so as not to make the blade damaged.
3. Any unusual voice, stop and check. Adjust chains and screws if they are loose.
4. Do stop the machine when there is problem. Do not put hands in when the machine is still working.
5. Add oil to cycloidal needle wheel on time (usually once per three months) .
6. After being operated for long time and the machine fails to cut off material, customer should adjust the knife and check whether the blade is damaged and need repairing.
7. In case the material-sending roller can not send the material smoothly, you should firstly
check and adjust rotary switch; if it can not work effectively, replace a new one in time.
8. Do not install the springs at each side too heavily or the material will not be sent smoothly. New machine please add proper amount of powder to the Roller to avoid material rolling and jammed.
RUBBER STRIP CUTTING MACHINE
用途:用于橡胶切条、切纸等。
特点:1.装有防护装置在使用时安全快捷。
2.翻滚切割,三个刀片设计,切料速度快,效率高。
3.送料速度可调,裁断宽度可调。
Purpose:This machine is used for cutting the rubber, paper etc.
Advantage: 1. Equiped with safety cover to secure safety on working .
2. Revolving blade cuts rubber in high speed and efficiency, with three blade edges.
3. adjusting the width of rubber strip through the speed button on the side.
使用说明:(中文:参考之前的广告册)
英文如下:
1. when operating, do not cut rubber in double-deck at one time, which will cause
the MOTOR to be too hot and broken. If the Material-sending Roller can not run smoothly, please shutdown at once; meanwhile, if there are odds and ends at knife edge, please clean up in time. Do stop the power before cleaning.
2. No iron or stone in the material; if any, take them
away at once, so as not to make the blade damaged.
3. Any unusual voice, stop and check. Adjust chains and screws if they are loose.
4. Do stop the machine when there is problem. Do not put hands in when the machine is still working.
5. Add oil to cycloidal needle wheel on time (usually once per three months) .
6. After being operated for long time and the machine fails to cut off material, customer should adjust the knife and check whether the blade is damaged and need repairing.
7. In case the material-sending roller can not send the material smoothly, you should firstly
check and adjust rotary switch; if it can not work effectively, replace a new one in time.
8. Do not install the springs at each side too heavily or the material will not be sent smoothly. New machine please add proper amount of powder to the Roller to avoid material rolling and jammed.